Dilden
Bros. co-owner Wayne Findley works in the field with Mike McCall on a job at an
Indiana farm. The farm’s water issues had limited its potential. Photo by Joe
Bradfield.
The dense gray dust clouds that rose up from the super single tires drifted little before settling back down on what should have been an Indiana cornfield.
The farmer who owned the section reported a 3 bushel per acre yield this year, far from enough to justify the cost of planting it. However, an orchard across the road had proven that irrigation could make the land profitable.
Dilden Brothers Drilling Company of Lafayette, Ind., used its Atlas Copco T2W Series III drill rig-the first of its kind-to create the first of two 168-foot-deep wells bringing relief both to the thirsty ground and to the farmer, who won’t have to watch the rain gauge as closely next year.
Dilden Bros. drilled the well to within 20 feet of final depth the first day with a 17 inch tricone, returning the next day to complete it to total depth and set a 20-foot section of 100-slot stainless steel screen at the bottom beneath 12-inch steel casing. They backfilled the annulus around the screen with gravel and developed the well with air until it was clean and producing the maximum yield possible.
Wayne Findlay co-owns Dilden Bros. with brother Don Findlay. Wayne said about 2 feet of topsoil lay above the sand and gravel that ran to 170 feet with a static water level of 81 feet. For the most part, any rain falling on the field drained too rapidly to fully benefit the crops at the surface. Fortunately, there was a plentiful supply of water available. He expected the well to produce over 1,000 gallons per minute.
The
Dilden Bros. crew puts Atlas Copco’s T2W Series III drill rig to work. Dilden
helped the company develop and fine tune the new version of the rig through
rigorous field testing. Photo by Joe Bradfield.
The large-bore well represents just one end of the spectrum of jobs Dilden’s T2W performs on any given day, and Wayne said the T2W was the perfect fit for all of the company’s specialties.
The rig had just been used Friday for a residential water well. Now in the cornfield on a Monday morning, Wayne said, “Switching over to this job just means hauling a pipe trailer and taking some bigger tools.” Dilden has favored the T2W for this very reason ever since it first purchased one in 1996.
When Atlas Copco was looking to update the T2W they met with drillers to find out what improvements should be made. As Dilden Bros. has a long history with T2W rigs, it’s no surprise the company stepped forward to offer input and their desire to purchase the first T2W Series III. Wayne and Don, who worked closely with the development team, were excited by the redesigned carousel and other changes. Dilden’s other rig is also a T2W, as was the one they traded for the Series III.
Atlas Copco worked with Dilden to tailor the new rig’s options specifically for their operation. Though the bulk of Dilden’s business had been water well drilling and installation, since about 2008 they now find they are being called upon more and more for geothermal services. So Atlas Copco bumped up the capacity of the 3-inch carousel from nine rods to 12 rods. The rig now also allows the driller the ability to backload the carousel from the rod box, allowing uninterrupted pipe handling.
“We wanted it for geothermal, for less time spent handling rod. The more you can do it with the rig, the better,” Wayne said. “But now we also use it in our water well applications.”
The upgraded rig’s swing-in carousel design brings the pipe over the hole, instead of moving the head to a fixed carousel. The head still moves aside to the right, for instance during case-setting, but when it’s called for, the head always returns exactly to center over the hole.
Then, too, Wayne said he liked how the swing-in carousel stows for transportation. It centers itself over the truck rather than to the side of it. “I have always felt that a swing-in carousel was better for the road,” he said.
“It’s
a very fast rig. Easily keeps up with bigger models,” says Wayne Findley, as
his crew gets the job under way. He attributes the rig’s speed to a
well-designed, three-speed head; the feed system; and its rod handling. Photo
by Joe Bradfield.
The new rig continues the T2W solid boom tower design, which provides ample clearance to perform such work as welding casing. Wayne said, “I can work around it. It’s a lot less restrictive for working with large diameter tools and casings.”
The irrigation well at this site demonstrated the T2W rig’s ability to switch quickly and easily from rotary mud to air drilling. It was a simple matter of changing a hose from the mud pump piping to the compressor and switching from the 65⁄8-inch drill pipe to working with the 3-inch drill pipe that was in the carousel.
Whatever job the T2W is on, Wayne appreciated its speed: “It’s a very fast rig. Easily keeps up with bigger models.” He attributed its speed to three things: a well-designed, three-speed head; the feed system; and its rod handling. “You get the same quick feed rate from it going up as you do going down (190 feet per minute). Not many other rigs that can say that. And this last rig, in 10 years I never had to touch its feed system.”
The rig is available with a variety of air packages. The largest is a 900 cfm, 350 psi (425 L/s, 24 bar) model. It also comes as 750/300 (355 L/s, 14 bar), 500/200 (236 L/s, 14 bar) and no air configurations.
Truck Options
Dilden got exactly the rig they wanted by knowing exactly what they wanted. John Baker, who has worked at Dilden for 22 years, said that’s because Wayne, his boss, actually drills on the rigs. He admires him for working alongside his men, but said also, “What’s nice about working for an owner who drills himself is that it means we always get the good stuff.”
As for the carrier, Dilden was pleased with Atlas Copco’s accommodations. “Once again,” Wayne said, “they made a special truck for us, just the way we wanted it.”
Don
Findlay keeps the office humming along while his brother, Wayne, works in the
field. Photo by Joe Bradfield.
Dilden’s rig also has the optional hydraulic front axle assist, which gives the driver near all-wheel-drive capability without raising the truck height. Wayne said they decided to go with super single instead of dually tires on the rear. There are many other options on the T2W including mud pumps, pipe spinner, sand reel, water injection, service hoist and more.
It took a while to customize the rig exactly to Dilden’s specifications and get it tuned just right. But Wayne was pleased with the results. He said, “Since we got it all dialed in correct, there hasn’t been a problem at all.” It has been running smoothly, and cool: “The cooling is fabulous, thanks to that large radiator.”
Tom Moffitt, U.S. sales manager for Atlas Copco water well drilling rigs, said, “We were very willing to do all of these things for Dilden Bros. on the T2W,” noting that Wayne and his crew’s feedback has been instrumental in making a rig that has always been popular in the Midwest even better. Many of the features Dilden Bros. requested for their rig, Moffitt said, are standard options now that make the T2W appealing to a wider customer base. ND
Report Abusive Comment